In a situation where the amplification mechanism is faulty, then your sound system is likely to give a poor output. The work of an amp is to raise the level of an electrical signal to a level that can be fed to the targeted output device which can be a speaker or a headset. This means if the speaker is producing a weak sound, the problem can be traced back to the amp and correction made. Amplifier repair may be required also if the output is distorted or it is not clear.
Normally, it is easy to troubleshoot amplification systems since most of them are constructed in a way that you can view all internal components and identify the faulty one. A number of steps are followed in accomplishing repair of an audio system. The first thing is to unplug the device from the wall and place it on a spacious table.
Screw driver is utilized in loosening the covers so that they can be removed. Complicated methods of troubleshooting are applied once the technician cannot identify any burnt component using his eyes. An odor will be noticed if there is a burned transistor and the system is opened immediately it stops operating.
Use the service manual provided by the manufacturer to identify the power transistors. While the power is on, a multimeter is used to check whether there is voltage in the pins of the transistors composing the device. The same should be done for all power ICs identified. The repairer will look for the fuse and test it for continuity.
Troubleshooting can proceed to other parts of the device if its power supply is fixed. A freezer will be used to look for presence of faulty components in the system. What happens is that all components are given a short burst and then the power put on. The last element to clear moisture is the one which is damaged.
A faulty element is removed using heat from a gun to melt the solder holding it in place. A needle nose pliers is the suitable tool to apply in puling the pins out of the board. Remove the screws holding the board in position so that you gain access of all sides. Cleaning of the holes left on the board is done through utilizing a solder wick.
Through use of the manual, it is possible to identify the component that is not working. A new one is then acquired and soldered at the same position and orientation. While inserting the pins of the element into the holes, one should be careful so that he does not bend them. Only enough solder should be applied so that the pins are not short. A side cutter is applied in clipping off the excess pins so that they do not protrude from the underside of the circuit board.
Testing begins with fitting the circuit board back to its place after replacing the spoiled element. The appliance is plugged onto power supply and its power button put on. Once the repairer is convinced that the system is back to its normal working, he will put off the power and then fasten the covers.
Normally, it is easy to troubleshoot amplification systems since most of them are constructed in a way that you can view all internal components and identify the faulty one. A number of steps are followed in accomplishing repair of an audio system. The first thing is to unplug the device from the wall and place it on a spacious table.
Screw driver is utilized in loosening the covers so that they can be removed. Complicated methods of troubleshooting are applied once the technician cannot identify any burnt component using his eyes. An odor will be noticed if there is a burned transistor and the system is opened immediately it stops operating.
Use the service manual provided by the manufacturer to identify the power transistors. While the power is on, a multimeter is used to check whether there is voltage in the pins of the transistors composing the device. The same should be done for all power ICs identified. The repairer will look for the fuse and test it for continuity.
Troubleshooting can proceed to other parts of the device if its power supply is fixed. A freezer will be used to look for presence of faulty components in the system. What happens is that all components are given a short burst and then the power put on. The last element to clear moisture is the one which is damaged.
A faulty element is removed using heat from a gun to melt the solder holding it in place. A needle nose pliers is the suitable tool to apply in puling the pins out of the board. Remove the screws holding the board in position so that you gain access of all sides. Cleaning of the holes left on the board is done through utilizing a solder wick.
Through use of the manual, it is possible to identify the component that is not working. A new one is then acquired and soldered at the same position and orientation. While inserting the pins of the element into the holes, one should be careful so that he does not bend them. Only enough solder should be applied so that the pins are not short. A side cutter is applied in clipping off the excess pins so that they do not protrude from the underside of the circuit board.
Testing begins with fitting the circuit board back to its place after replacing the spoiled element. The appliance is plugged onto power supply and its power button put on. Once the repairer is convinced that the system is back to its normal working, he will put off the power and then fasten the covers.
No comments:
Post a Comment